A Joystick effect that I want to use as a normal effect

Discussion relating to the Korg M50 Workstation.

Moderators: Sharp, X-Trade, Pepperpotty, karmathanever

Post Reply
User avatar
Lenster
Posts: 42
Joined: Sat Dec 15, 2007 11:13 pm
Location: Levittown, PA U.S.
Contact:

A Joystick effect that I want to use as a normal effect

Post by Lenster »

I have searched the forum and this question was not found. So...

I want to modify Prog D 42 SynBrass The Sailor. The sound what I need is achieved when I push the joystick forward (JS+Y). (Like a wavy vibrato)

I believe that it is an LFO parameter, but not sure where to find or change it.
What I want is to have that effect without keeping the joystick pushed forward. Right now I am using duct tape to hold the joystick up and it is just awkward.

Just in case I really bugger-up the patch I copied it to Prog E 100 which was unused.
If anyone can point me in the right direction, Much appreciated. Thanks. - Lenster
billbaker
Platinum Member
Posts: 2206
Joined: Wed May 31, 2006 11:56 pm
Location: Vienna, Virginia, USA
Contact:

Post by billbaker »

The question you need to ask is what's being modified by the JS push?

If it's volume - aaAAaaAAaaAA - then look in the amp section.

If it's filter - ooo-wow-ooo-wow - then look in the filter section.

The answer will tell you where to look.

That's the key, LOOK. Because either way you should see a piece of the programming that will say either Joystick or have the abbreviation JS+Y in the AMS (alternative modulation source) assignment. Where "JS+Y" appears will tell you where and what to modify, and by how much.

If the JS variation is, say +50, then you want to increase the modulation of the basic parameter (yes, probably an LFO) that the JS is controlling from it's dry/zero modulation to a constant modulated state.

- - - - - - - -

Many programs let you freeze the joystick position by pushing SW2 - you might want to check that as well; a rewrite may not be necessary.

You may have the option of selecting mode for the AMS as well; rather than temporary/momentary you may be able to select for toggle operation which means that the modulation would be full-on and stay there until the next push when it would return to zero/dry -- rotary speaker works this way on most organ sounds.


Hope this helps.


BB
billbaker

Triton Extreme 88, Triton Classic Pro, Trinity V3 Pro
+E-mu, Alesis, Korg, Kawai, Yamaha, Line-6, TC Elecronics, Behringer, Lexicon...
User avatar
Lenster
Posts: 42
Joined: Sat Dec 15, 2007 11:13 pm
Location: Levittown, PA U.S.
Contact:

Post by Lenster »

Thanks Billbaker, for the response.

When I read your response it makes sense. When I look in the M50, all I see is a lot of assignments for JS-Y and nothing for JS+Y.

I tried modifying a few things and got some wierd reactions but not what I am attempting to do.

I was hoping to see some parameters change as I move the joystick, but I don't think the M50 shows that kind of dynamic stuff.

I will continue to experiment. I'm playing with a prog copy so I am not afraid of trashing the original prog. I will post if I find it.
- Lenster
User avatar
Lenster
Posts: 42
Joined: Sat Dec 15, 2007 11:13 pm
Location: Levittown, PA U.S.
Contact:

Post by Lenster »

Found what was looking for.
Adjusted LFO-1 pitch intensity, and that was it.

It took touching everything and seeing what changed. Eventually stumbled upon it.

Thanks BB for your guidance !!!
Post Reply

Return to “Korg M50”