Motion sequence aint recording right

musikmachine · Post by **musikmachine** » Sat Jan 26, 2008 3:59 am

Is it a bug?I press motion sequence and record the motion sequence.The record light says on for another 4 measures and the motion sequence doesn't play back as i recorded it,it plays back to front!Any idea why?Don't know what OS i have but i'm sure i updated it when i first got it.The rec light should go out after 8 bars so that must be to do with it.It's like it starts recording the changes 4 bars late

robosardine · Post by **robosardine** » Sat Jan 26, 2008 1:25 pm

Try saving your data to card. Then do a factory reset. then try reording a motion sequence on a pattern using a metronome count in. Then try one without a count in, What happens then?

musikmachine · Post by **musikmachine** » Fri Feb 01, 2008 6:41 am

robosardine wrote:Try saving your data to card. Then do a factory reset. then try reording a motion sequence on a pattern using a metronome count in. Then try one without a count in, What happens then?

Haven't got round to it yet but i will.I'd like to record the motion sequences and then record the midi patterns into live for further editing(or to audio) instead of having to go trough clip automation(never mind live use!).Hope it's not a fault

inducejack · Post by **inducejack** » Sat Feb 02, 2008 11:09 am

you from alabama too?????

musikmachine · Post by **musikmachine** » Sat Feb 02, 2008 11:46 pm

inducejack wrote:you from alabama too?????

No other side of the pond

Why?

Setsonics · Post by **Setsonics** » Sat Mar 08, 2008 3:10 am

Damn, I am having this problem, why would it be doing this?

Is it a faulty unit?

It's always done this I think, but I am now getting into more motion sequencing and it records an extra measure after I take off record, PLUS, it bumps the first measure forward one.

Hmm.. I am going to fight with this some more.

Do you really think I need to reset my ESX and test it like that?

I might try... But I got a song to work on,.

=)

Setsonics · Post by **Setsonics** » Sat Mar 08, 2008 3:14 am

musikmachine wrote:
inducejack wrote:you from alabama too?????
No other side of the pond

Why?

Heh.

*Update!*

I got by it (painstakingly) by recording the motion sequence one measure BEHIND where I wanted it.

That was just painful, I better not have a faulty ESX or heads will roll, I use this thing EVERY DAY of my life!

Boo I say.

Boo.

musikmachine · Post by **musikmachine** » Sat Mar 08, 2008 10:21 am

Setsonics wrote:Damn, I am having this problem, why would it be doing this?

Is it a faulty unit?

It's always done this I think, but I am now getting into more motion sequencing and it records an extra measure after I take off record, PLUS, it bumps the first measure forward one.

Hmm.. I am going to fight with this some more.

Do you really think I need to reset my ESX and test it like that?

I might try... But I got a song to work on,.

=)

May be a bug as two units are doing the same thing..

I haven't used my MX for a while but was planning to break it out so i think i'll do a reset.I ay be sellig mine so i need to know if this is a fault or a bug..I hope the latter!

Setsonics · Post by **Setsonics** » Sat Mar 08, 2008 12:32 pm

Well I own an ESX, so it's spread across two models then!

musikmachine · Post by **musikmachine** » Sat Mar 08, 2008 4:18 pm

Setsonics wrote:Well I own an ESX, so it's spread across two models then!

I'll reset mine and see what happens..I'll post the outcome later

starving student · Post by **starving student** » Sun Jan 18, 2009 9:23 am

so what happened you two, did you resolve the issue?

Dj Pound · Post by **Dj Pound** » Mon Jan 19, 2009 12:31 am

did you try clearing the entire motion sequence, before rerecording your own?

Sometimes i forget to do this and it makes things really difficult.