Page 1 of 1
Radias Timeout(device inquiry error)
Posted: Wed Oct 01, 2008 12:58 am
by kcered92
I have an intel based mac and it will not receive program dump from radias. I am running the version 2.0 update and software recognizes midi connection but will not receive or deliver programs. I keep getting the message Device inquiry error. If anyone can help that would be great.
[/img]
Posted: Wed Oct 01, 2008 5:28 am
by Dionysos2
Check if you USB-Cable is not longer than 2metres otherwise use an Repeater-USB Cable.
That was my problem.
Posted: Wed Oct 01, 2008 8:04 am
by Fierball
Also be sure you have the latest version of the Korg USB MIDI driver. (I think it's 1.0.8). I have the same setup, and the MIDI port options are different than yours.
Mine lists "RADIAS - KBD/KNOB" for MIDI IN, and "RADIAS - SOUND" for MIDI OUT. There's no option for "RADIAS DUMP..." in my version.
The RADIAS is a relatively new device, so to have the correct profile, you need the latest driver. You can get the latest version <a href="
http://www.korg.com/service/downloadinf ... 6">here</a>.
Fierball
Posted: Wed Oct 01, 2008 1:23 pm
by slammah2012
Do you have both the Radias Firmware at 2.0 and the updated editor software for 2.0 with the added destinations???
is sysex in global set to on and saved???
Did you try the 2 other ports???(radiasKnob/kbd)
Midi in is at the Midi in of the radias...
Midi out is at the out of the radias...
this will not help with the usb transfer
Posted: Thu Oct 02, 2008 4:17 am
by kcered92
Everything is up to date. There must be a problem with my usb. Im going to give that a try.. thanks for the help. If that doesn't work then Im clueless about the situation.
Posted: Thu Oct 02, 2008 5:42 am
by slammah2012
OKay....
Just make sure you don't use midi in and midi out as your connection ports....
it should be "radias sound" and "radias knob".....
Posted: Fri Oct 03, 2008 12:43 am
by kcered92
The problem is I dont get the knob/sound option. Only radias (dump) update. I hate the compatibility with hardware and software, it seems to be a persistent problem.
Posted: Fri Oct 03, 2008 12:51 am
by slammah2012
kcered92 wrote:The problem is I dont get the knob/sound option. Only radias (dump) update. I hate the compatibility with hardware and software, it seems to be a persistent problem.
what OS??
on xp.....every thing reads fine 4 me...
nb.
winows xp only allows 10 midi devices installed in the registry........
one other thing.........
make sure protect is off in global....
Posted: Mon Oct 06, 2008 8:53 pm
by kcered92
OSX for mac. I have an intel mac. The problem will not go away. It will not let me exchange any programs....tried everything(even switching usb cables)
Posted: Tue Oct 07, 2008 12:28 am
by slammah2012
kcered92 wrote:OSX for mac. I have an intel mac. The problem will not go away. It will not let me exchange any programs....tried everything(even switching usb cables)
I have heard of USB problems on Macintosh's...
Have you access to a different computer to fault find with???
Cubase -- Device control panel
Posted: Thu Oct 09, 2008 12:04 pm
by Jarred Cassidy
Has anyone created a device control panel for the radias for cubase 4 ...
Re: Cubase -- Device control panel
Posted: Thu Oct 09, 2008 1:08 pm
by slammah2012
Jarred Cassidy wrote:Has anyone created a device control panel for the radias for cubase 4 ...
The Korg Radias Editor is a Control panel for the Radias....
Can't its knob movements (CC# and preset selection on editor)be recorded in cubase4 as CC# events through its multple Midi ports???
Posted: Thu Oct 09, 2008 6:07 pm
by meatballfulton
Radias Dump is not a valid port...if you don't see the Sound/Knob options something is not properly installed (doh).
Are you running Leopard? Make sure you have the latest version of both the USB drivers and editor available from Korg's website. There were problems with earlier versions and Leopard.