KP3 error codes

[rhubarb]

Ran a full inspection (Internal and External) on my KP3...

CONNECTION[SEND]& [4] + [TAP/RANGE]



Came up with Er.5.1, Er.6.1 and Er.7.1

Anyone know what these are?



Thanks!

[eeclark]

Ran a full inspection (Internal and External) on my KP3...

CONNECTION[SEND]& [4] + [TAP/RANGE]



Came up with Er.5.1, Er.6.1 and Er.7.1

Anyone know what these are?



Thanks!

Did you ever find out?

[eeclark]

Error Code
2006.8.30 KORG PD3 T.Kanai English by M.Y.
: Skipping the Audio Loop Back Inspection and the USB check : Skipping the MIDI Loop Back inspection and the USB check.
: Skipping the Audio Measurements and PAD surface inspection : Audio Measurement only
: PAD all surface inspection only
: Full inspection (Internal and External)
: External inspection
: Display of System Version : Load the Preset
: IPL Mode
: Step Up (When an error occurred in the internal inspection, retry the inspection.) : Step + (Move within the item)
: Step - (Move within the item)
: Item Number Up
: Item Number Down
: When an error occurred in the internal inspection, skip the inspection
KP3 displays the Error Code in the LED, when an error occurred in the internal inspection. 4 digits of the LED indicates the error code.
[Er.**] * (Ten's digit) : Item number (item of the internal inspection) * (One's digit): Test number( In the internal inspection)
Item 1. DSP IF Check
2. DSP - SDRAM Check
3. CPU ROM Check
4. EEPROM Check
5. Loop Back Check (Audio) 6. MIDI Loop Check
7. Card Check
8. USB Check
Notice: When the start-up condition or the forwarding between CPU <-> DSP is NG, KP3 cannot start the test mode, because after the forwarding the Boot code, KP3 moves to the self check sequence (TEST MODE).
*USB check needs a special computer, so skip by [SAMPLE BANK A] + [TAP/RANGE] when an error occurred in the inspection.
*Initial Settings
Set the volumes and the switches like followings.
CONNECTION INPUT Select INPUTVR
Fx Depth Slider PHONES VR MICTrim:MAX
: SEND : LINE :MAX :MIN
: MIN (0) :MAX :MAX
Connection for the automatic inspections
Cable
LINE OUT L LINE OUT R MIDI OUT
→ → →
LINE IN L LINE IN R MIDI IN
RCA cable RCA cable MIDI cable
SDCard (ProtectOFF)
(Caution:) Use the AC Adaptor of KA-20*series
Internal Inspection
1. DSP IF Check
When an error occurred, the inspection stops displaying [Er.11]-[Er.13] in the LED display.
2. DSP SDRAM Check
When "Data Error", the inspection stops displaying [Er.22] or [Er.23] in the LED display. When "Address Error", the inspection stops displaying [Er.21] in the LED display.
3. CPU ROM Check
When "Checksum Error", the inspection stops displaying [Er.31] in the LED display.
4. EEPROM Check
When "Verify Error", the inspection stops displaying [Er.41] in the LED display. 5. OVER LOAD Line Check ( Audio LoopBack )
<<<In>>>
a: OUTPUT Lch(LINE IN (Rch: GND Level)
Connect the LINE OUT(L) to the LINE IN(L), when the level of the LINE IN(L) is out of the decided range, the inspection stops displaying [Er.51] in the LED display.
Connect the LINE OUT(L) to the LINE IN(L), when the level of the LINE IN(R) is more than the decided level, the inspection stops displaying [Er.52] in the LED display.
b: OUTPUT Rch(LINE IN (Lch: GND Level)
Connect the LINE OUT(R) to the LINE IN(R), when the level of the LINE IN(R) is out of the decided range, the inspection stops displaying [Er.53] in the LED display.
Connect the LINE OUT(R) to the LINE IN(R), when the level of the LINE IN(L) is more than the decided level, the inspection stops displaying [Er.54] in the LED display.