Korg Forums

I have tried moving a Triton sound to the M3 and was wondering what you do about the multi-samples. The Triton has only the high and low multisample. The M3 has 4 different ones. I was wondering where the best place for each of the Triton's multisamples would be. I see that I can pick different ...

Hi, Jerry I tried another smaller stick and deleted all the apps on it before I put the PCM data on it. It worked perfectly. What I wanted to ask, though, so that I can use the U3, is can I have the Version 2.0 folders on the stick with the PCM data in case I ever need to reinstall? Also, will ...

This is maddening. I cannot figure out what I'm doing wrong. I have to have the M3 scan the USB device before it will even recognize that there is something on it. I think that may be why it's not autoloading. I have to go through the entire process of scanning the USB stick, then loading each EXPCM ...

I managed to load all the voices. Now, I'm trying to make it autoload, but it's still not doing that. But I can hear the Piano Voice now when I go into the media tab and load each Volume of sounds. It's just that they don't autoload when I turn the M3 back on. I have to do it all over again even ...

I got the EXB-256 sampler ram and proceeded to upgrade my M3M to version 2.0. The M3M says that it is now version 2.0 expanded as I expected after following the steps of the upgrade. However, the Stereo Grand 4-Way 2 EX3 is not anywhere to be found. Not at A000 or at A020 (the names of the two are ...

How did you get the midi device to work? How are you configured to record the M3 into logic? I am trying to get mine to work in Logic 8 and haven't a clue.

Thanks.

fm

I bought the Firewire card for my M3M as soon as it came out. BIG MISTAKE. It's a POS from the word go. The latency is unbelievable. I read all the threads on it and tried as hard as I could to remedy the situation, it's still latency city. I have a Mac Pro with 4 gigs of ram. There should be ...

I have a Triton Classic and I want to move some of the voices over to my M3 so that I can use the M3 at rehearsal and leave the midi keyboard there and take the M3 home to use with the Triton at home. I don't need all of the Triton's voices, I just want to move over patches that I use for gigs ...

Hallelujah! I think I get it now. That Total Recall and Data Sync page on the software setup is a bit misleading, I think, especially since it automatically tries to transmit whatever is in it, so one just assumes that it's necessary for the unit to do that. So, I completely cleared that thing ...

Okay, here's the thing. If I don't have the M3 editor set to receive all from the M3, when I go to get a patch on the editor, there are no patch names there. So, instead, I have to receive damned near all the freaking program, combi banks and drum kits just to be able to use the editor. And that's ...

Is there anyone else on the list using the firewire card for the M3? This thing is so unbelievably slow I can't believe they released it. It cannot possibly be functioning as it is supposed to. This is just plain punishment. I have been waiting for over 2 hours for this piece of s**t to load the ...

Yes, I will do that on Monday. I have the thing working now, which is encouraging. I got the Mac Pro to see both firewire ports (I had to go into Network settings and make sure the firewire wasn't set up to do anything with the network), then I went to MOTU and updated the driver on the Traveler. I ...

Well, this morning I opened up Logic and voila! it's finally trying to see the M3 through the fire wire cable! However, the transmission is unbelievably slow. It takes 3 to 4 minutes just to transmit the information of one bank from the editor to the M3. The USB was way, way faster than this. This ...

I have definitely got the midi exclusive enabled in Global Mode. I've been reading the manual, too, and as far as I can see, I'm doing everything that they are asking. I will keep at it today. I just keep getting this behavior where there is no recognition between the editor and the M3 itself ...

Well, one problem is solved. I had the card seated incorrectly. Fortunately, the M3 shows that it is working now. I took Jerry's advice, and plugged the M3 straight into the Mac. The Mac recognizes the M3, it even says M3 under the system profile, firewire port. So I know that's working. What I ...