View previous topic :: View next topic |
Author |
Message |
schmoelzel
Joined: 27 Feb 2024 Posts: 3
|
Posted: Tue Feb 27, 2024 1:06 am Post subject: Korg M1 - advancing through the programs |
|
|
Hello from Canada......total Korg M1 newbie here. Picked one up a little while ago and really love this keyboard and it's sounds. One annoying thing I can't figure out is how to advance through the sounds. In the manual it says to press the PROG key and then use the up/down keys. However, when I press the PROG key, the flashing cursor is always under the first editing function. Pressing the up/down keys changes this function (osc I think). Is there a secret on getting the cursor to appear in the Program name area? Any help is appreciated. BTW, I can advance through the various sounds but I have to use the number keys. |
|
Back to top |
|
|
the_crimson_thunder Junior Member
Joined: 18 Nov 2014 Posts: 92 Location: Germany
|
Posted: Tue Feb 27, 2024 12:44 pm Post subject: Korg M1 - advancing through the programs |
|
|
Hi schmoelzel - welcome to the forum!
A 'normal' working M1/M1R lets you trawl through the PROGS/COMBIS by using the numeric buttons as well as the UP/DOWN buttons...
...so the behaviour of your synth is a bit strange
Have you already tried to reset (initialize) the synth? If not here's the procedure:
Turn OFF the synth. Now press AND hold the [INT], [CARD] and [COMBI] buttons and turn the synth ON. The ROM (=firmware) version will be displayed on the display's right side (two digits), and the M1's data will be initialized. This erases ALL internal data so after this procedure you have to reload the patches via MIDI or by using a cartridge. So if there are patches you want to keep please save them BEFORE you initialize the M1!
Hope this helps...
Best,
the crimson thunder |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3780
|
Posted: Tue Feb 27, 2024 1:12 pm Post subject: |
|
|
Does the cursor re-appear below the Program number if the Prog button is pressed again?
Has the internal battery been replaced recently?
. |
|
Back to top |
|
|
schmoelzel
Joined: 27 Feb 2024 Posts: 3
|
Posted: Tue Feb 27, 2024 7:37 pm Post subject: Re: Korg M1 - advancing through the programs |
|
|
the_crimson_thunder wrote: | Hi schmoelzel - welcome to the forum!
A 'normal' working M1/M1R lets you trawl through the PROGS/COMBIS by using the numeric buttons as well as the UP/DOWN buttons...
...so the behaviour of your synth is a bit strange
Have you already tried to reset (initialize) the synth? If not here's the procedure:
Turn OFF the synth. Now press AND hold the [INT], [CARD] and [COMBI] buttons and turn the synth ON. The ROM (=firmware) version will be displayed on the display's right side (two digits), and the M1's data will be initialized. This erases ALL internal data so after this procedure you have to reload the patches via MIDI or by using a cartridge. So if there are patches you want to keep please save them BEFORE you initialize the M1!
Hope this helps...
Best,
the crimson thunder |
thank you for the tip. When I got the keyboard, it did not boot-up. I did the battery replacement and then reinstalled the programs via midi. I guess I can do this again and see if that helps. |
|
Back to top |
|
|
schmoelzel
Joined: 27 Feb 2024 Posts: 3
|
Posted: Tue Feb 27, 2024 7:39 pm Post subject: |
|
|
voip wrote: | Does the cursor re-appear below the Program number if the Prog button is pressed again?
Has the internal battery been replaced recently?
. |
Cursor doesn't appear below the prog #. Have pressed it multiple times. Yes, I did replace the battery and reinstalled the voices (programs). I can advance through the programs via the # pad. |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3780
|
Posted: Tue Feb 27, 2024 8:18 pm Post subject: |
|
|
A stuck-on Cursor Key could have been a possible reason for the observed behaviour. If that was the case, pressing the Prog key would have moved the cursor back to below the Program number. If it doesn't do this, then something else is causing the issue.
Does the problem still occur if all MIDI cables, pedal cables, and output cables are disconnected? When replacing the main board in the M1 after a backup battery replacement, there is a chance some wires can become trapped between the main board and the case. I'm not sure if the wires that can become trapped have anything to do with the issue, but it's worth checking. Also check that no connectors have become dislodged.
. |
|
Back to top |
|
|
|