![Korg Forums Forum Index](templates/subSilver/images/logo_phpBB.gif) |
Korg Forums A forum for Korg product users and musicians around the world. Moderated Independently. Owned by Irish Acts Recording Studio & hosted by KORG USA
|
View previous topic :: View next topic |
Author |
Message |
gaztech
Joined: 25 May 2018 Posts: 5
|
Posted: Sun Jan 16, 2022 7:34 am Post subject: Schematics or Service Manual EA-1 |
|
|
Hi guys,
Does a schematic or service manual exist for the Electribe EA-1?
I have one in for repair with no sound. I traced right up to the DAC and there is nothing there. I'm going to have to go deeper.
Without a schematic at least it going to be difficult!
Anyone have anything? ![Confused](images/smiles/icon_confused.gif) |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
gaztech
Joined: 25 May 2018 Posts: 5
|
Posted: Fri Mar 11, 2022 4:21 pm Post subject: |
|
|
So... Now I have output just after the DAC.
I found badly soldered resistor. Could only see it through a large magnifier. I have both channels so progress has been made!
Now I have very low output on the output section. All outputs are low but I do have some signal at the volume control and onwards. I suspect that the wrong power supply was used on this one.
If I could JUST get a schematic of the output section then that would enable me to finish this one off. Without the schematic (and it's NOT the same as the other units) I'm having a hell of a time getting this one done.
Anyone have anything at all? |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
gaztech
Joined: 25 May 2018 Posts: 5
|
Posted: Fri Mar 11, 2022 4:23 pm Post subject: Electribe EA1 Schematic |
|
|
So... Now I have output just after the DAC. I have both channels so progress has been made!
Now I have very low output on the output section. All outputs are low but I do have some signal at the volume control and onwards.
If I could JUST get a schematic of the output section then that would enable me to finish this one off. Without the schematic (and it's NOT the same as the other units) I'm having a hell of a time getting this one done.
Anyone have anything at all? Oh, and it's not the mutes. Even with them taken out it doesn't work. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
otzcz
![](images/avatars/gallery/YaBB/winnie.gif)
Joined: 22 Sep 2019 Posts: 29 Location: Prague
|
Posted: Thu Jun 09, 2022 11:16 pm Post subject: Re: Electribe EA1 Schematic |
|
|
gaztech wrote: | So... Now I have output just after the DAC. I have both channels so progress has been made!
Now I have very low output on the output section. All outputs are low but I do have some signal at the volume control and onwards.
If I could JUST get a schematic of the output section then that would enable me to finish this one off. Without the schematic (and it's NOT the same as the other units) I'm having a hell of a time getting this one done.
Anyone have anything at all? Oh, and it's not the mutes. Even with them taken out it doesn't work. |
Hi, I also tried to find some original technical info for ER-1, but with little success. It looks like they hide it well
Maybe this could help a bit, or there's link to service manual for EM-1 in the description: https://www.youtube.com/watch?v=h0OfLD_NHDU _________________ Digitakt, ER-1, Volca Beats + Bass + Modular, Neutron, k-2, Microfreak, Liven XFM, Beatstep Pro, Keystep, UC-33e, few FX (Zoom G1four, Razzor DD+DS, EHX Platform+HolyStain, Samson C.com), Mackie 1202 VLZ4, pair of RCF AyraPro6 |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
gaztech
Joined: 25 May 2018 Posts: 5
|
Posted: Sat Jun 11, 2022 1:02 pm Post subject: |
|
|
Hi guys,
I forgot to add... This one is an ER-1 MK II version.
I actually managed to find an ER-1 service manual from one of the paid sites and bought it since I couldn't find it anywhere else but I find that the earlier version is very different so this manual is no good for this one.
It's the MkII version manual that I need. This one seems to be unobtainium. I can't find it anywhere.
However, the board that I have the issue with may be used in something else. That's very possible.
Board number is: KLM 2475
If anyone has a schematic for just this board then it would help enormously. I changed some chips out as the signal looked like it was dying after them but that didn't work (these surface mount boards are very difficult to trace out) - but I did manage to advance the signal a little further so a bit more progress!
If I had the MK II service manual I might be in with a chance to fix this thing.
As an aside... If someone wants the ER-1 manual I have then I can send it on if you need it. Just PM me... I checked all the other Electribe variants (EM-1 etc etc) but ALL of them are different to this one. None of them have the KLM 2475 board.
Still hoping someone will come up with something. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|