View previous topic :: View next topic |
Author |
Message |
drpanties
Joined: 30 Aug 2020 Posts: 4 Location: Las Vegas, NV
|
Posted: Sun Aug 30, 2020 5:26 pm Post subject: Program/Bank Switch commands in Triton legacy |
|
|
OK, please bear with me...Trying to use the Triton software as a replacement for my Triton Rack. The software's response to program change commands has me a bit flummoxed. I'd like to be able to call up the User banks of sounds via MIDI, but experimentation with Bank Switch commands has proved difficult. I can access the Factory Banks using CC 0 and CC 32 (values 0-3), and the EXB-PCM Banks using values 8-16. Whenever I discard the bank switch commands and use just program changes, the softward defaults to Factory Bank 1. Hope that is clear as mud. Can anyone else relate? Thx, P |
|
Back to top |
|
|
Bill1983 Junior Member
Joined: 06 Nov 2017 Posts: 93
|
Posted: Sun Sep 27, 2020 8:50 pm Post subject: Re: Program/Bank Switch commands in Triton legacy |
|
|
drpanties wrote: | OK, please bear with me...Trying to use the Triton software as a replacement for my Triton Rack. The software's response to program change commands has me a bit flummoxed. I'd like to be able to call up the User banks of sounds via MIDI, but experimentation with Bank Switch commands has proved difficult. I can access the Factory Banks using CC 0 and CC 32 (values 0-3), and the EXB-PCM Banks using values 8-16. Whenever I discard the bank switch commands and use just program changes, the softward defaults to Factory Bank 1. Hope that is clear as mud. Can anyone else relate? Thx, P |
Are you running Windoes or Mac. I just purchased the $399 Korg Collection. It installed perfectly and neither Ableton Live 10 orSonar Platinum recognizes the VST so I cannot do anything at this time. _________________ PA4x, PA500, NI Komplete Kontrol S88 MK2, Sonar Platinum, Ableton Live 10 Standard, NI Komplete12 Ultimate, EWQL Libraries, Nektar Impact LX88, Focusrite Scarlett 6i6 Gen2, Studiologic MP-117 Pedalboard |
|
Back to top |
|
|
drpanties
Joined: 30 Aug 2020 Posts: 4 Location: Las Vegas, NV
|
Posted: Mon Sep 28, 2020 2:31 pm Post subject: |
|
|
I'm running it on a Mac; El Capitan. I run it in standalone, not as a plug in. |
|
Back to top |
|
|
jdoo Junior Member
Joined: 06 Jan 2011 Posts: 54
|
Posted: Fri Nov 27, 2020 1:37 am Post subject: |
|
|
Just in case anyone else runs up against this same thing. I hit it also. Here is what I found..
Triton MIDI Mapping ( VST)
7 Bit (14 bit didn't work)
CC0 + CC32 + Program Change ( need three messages initially)
CC0 — once set — only need to change CC32
CC32 — once set — only need to do program change messages for the bank
Program Change MUST follow CC32 for bank to change
CC0: 0
CC32: 0-3 = Factory Banks A-D 8-16 = EXB PCM01-09 32-35 = User A-D
Program Change 0-127
CCO: 120
CC32: 0 = Drums
Program Change 0-127
CC0: 121
CC32: 0-9 = GM - GM(9)
Program Change 0-127
Anything other than these combinations = FACTORY BANK A
hth -
Joe |
|
Back to top |
|
|
drpanties
Joined: 30 Aug 2020 Posts: 4 Location: Las Vegas, NV
|
Posted: Fri Nov 27, 2020 5:34 am Post subject: |
|
|
Oh man, you're my hero. Tried it, works perfectly. Wonder why they buried the control change values...probably so some schlub like me would chase his tail. How'd you figure it out? - Doc |
|
Back to top |
|
|
jdoo Junior Member
Joined: 06 Jan 2011 Posts: 54
|
Posted: Fri Dec 18, 2020 6:36 pm Post subject: |
|
|
Hey Doc -
Glad it helped. I cant recall where i dug that up from. Part of it, I figured out through trial and error - but not all. Somewhere, there was a push in the right direction. I am just paying it forward.
Cheers & stay safe-
Joe |
|
Back to top |
|
|
Cubilas
Joined: 29 Jan 2013 Posts: 42
|
Posted: Mon Mar 18, 2024 7:02 pm Post subject: Thanks!! |
|
|
Hey jdoo -
Quote: | CC0 + CC32 + Program Change ( need three messages initially)
CC0 — once set — only need to change CC32
CC32 — once set — only need to do program change messages for the bank
Program Change MUST follow CC32 for bank to change |
I just wanted to say a huge thanks for providing this information and solution.
Much appreciated!! |
|
Back to top |
|
|
|