View previous topic :: View next topic |
Author |
Message |
fiddlerguy
Joined: 20 Mar 2016 Posts: 3
|
Posted: Sun Mar 20, 2016 2:43 am Post subject: SDD 3000 Noise |
|
|
I recently bought a SDD 3000. I'm very pleased with the features I've used so far. It's going to take me some time to understand all this pedal can do. One problem that is puzzling my is it adds a lot of noise to my signal chain. I've tried changing cables, moving it's position in the chain and even using it alone. Is this common? Should I have all this extra noise? My go to cable is mogami, so I'm not using cheap cables. I just don't understand where the noise is coming from.
Thanks for reading! _________________ Fiddlerguy |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3780
|
Posted: Sun Mar 20, 2016 10:33 am Post subject: |
|
|
What sort of input is the SDD 3000 going into, and what are the settings for the input and output attenuator switches and the effects selected when the noise is an issue?
. |
|
Back to top |
|
|
fiddlerguy
Joined: 20 Mar 2016 Posts: 3
|
Posted: Sun Mar 20, 2016 9:15 pm Post subject: |
|
|
Although I've run the signal without itand still gotten the hum I am using a Boss Looper pedal, after the SDD 3000 then to a Soundcraft MFXi 12 board and that feeds a Bose L1 model 1S.
Just checking the Input and output attenuation I found I had not set the input to the lowest setting, but did have it on the middle +16db with the input knob set at 2 the output was set to the lowest setting. That could account for some noise, but I don't think all of it.
When I ran it Instrument, to SDD 300, to Soundcraft mixer to Bose I still have a hum. It is significantly reduced, but it's definitely still there. _________________ Fiddlerguy |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3780
|
Posted: Mon Mar 21, 2016 9:28 pm Post subject: |
|
|
If hum is the main component remaining of the noise that can be heard, there are several possible sources. If you think the SDD 3000 is contributing to that hum, moving it (and the other effects units) away from mains power cables, and from other units with transformers in them might reveal the cause.
It's also worth checking the jack sockets are in good condition, and all their ground connections are secure.
If the hum is still there, the mains power supply for the SDD 3000 might be a source of hum. Feeding the SDD 3000 from a smooth 9V supply e.g. from a 9V battery might tell you something. (If you try this, take care because the centre pin of the plug that goes into the SDD 3000 is negative, whilst many, if not most electrical goods use centre pin positive. A PP3 battery probably won't be man enough to power the unit. A PP9 would be more suitable).
. |
|
Back to top |
|
|
fiddlerguy
Joined: 20 Mar 2016 Posts: 3
|
Posted: Mon Mar 21, 2016 9:55 pm Post subject: |
|
|
Thanks, I've been thinking about getting a pedal board power supply with isolated outputs. I will check all the grounds.
Thanks for your help. _________________ Fiddlerguy |
|
Back to top |
|
|
jfsolnet
Joined: 12 Sep 2016 Posts: 1
|
Posted: Mon Sep 12, 2016 3:33 pm Post subject: |
|
|
Hey there,
I'm having noise issues at only the +4db output attenuator settings no matter what cables or amp I'm using. I'm using a 1700ma 9v one spot power supply. It seems to resolve at -10 and -20db... Is this normal? Should I try a different power supply?
Thanks,
Jeff |
|
Back to top |
|
|
voip Platinum Member
Joined: 27 Nov 2014 Posts: 3780
|
Posted: Tue Sep 13, 2016 9:26 pm Post subject: |
|
|
What sort of source is being used, and what is the noise being heard? Is it hiss, hum, or buzz?
. |
|
Back to top |
|
|
|